LS-036M-25 Brushless Metal Gear Digital Servo

The approved product record lists LS-036M-25 as Brushless Metal Gear Digital Servo. The dimension drawing below is the approved drawing for this model - use it to check hub fit, arm clearance and mounting face before committing a build.

The scene photographs below come from the approved LS-036M-25 image set and show the servo as supplied, in RC and UAV control use within the LINQDOM RC & UAV Parts & Accessories line. Before integrating, confirm every point against the specification table in module 01.

The full parameter set is in the specification table in module 01 - the points below are the decisions rather than a second parameter list.

• Torque figures. The listed maximum torque is ≥25.0kgf.cm at 6.0V and ≥30.0kgf.cm at 7.4V. Treat these as the upper limits the unit is specified to reach, not as continuous working figures.
• Current. The listed stall current is ≤5.2A at 6.0V and ≤6.2A at 7.4V. The supply, wiring and connectors must carry that.
• Supply. The listed operating voltage is 6.0~7.4V DC. If your pack runs at 8.4V, this model’s listed range does not cover it — confirm the rail before ordering.
• Interface. The record lists a pulse width range of 500~2500μs but does not list a communication interface field for this model. Confirm the signal interface with the supplier before ordering.
• Construction. The record lists the case material as PA+30%GF with an aluminium mid-shell, and the motor type as brushless. Both are structural facts worth carrying into a mechanical review.

• A listed maximum torque of ≥30.0kgf.cm at 7.4V, among the highest torque figures listed in this package.
• A brushless motor with a metal gear train, as marked in the record.
• A case listed as PA+30%GF with an aluminium mid-shell, giving the mechanical review a documented construction to work from.
• A listed no-load speed of ≤0.12 sec./60° at 7.4V and ≤0.15 sec./60° at 6.0V.
• A 180°±10° operating travel angle with a 210° mechanical limit angle behind it.
• Consistent supply terms: the standard MOQ for this servo line is 100 pcs, and OEM/ODM requests are handled as project-specific enquiries.

LINQDOM is a Shenzhen-based B2B supplier with OEM/ODM sourcing and customization support, and the standard MOQ for this servo line is 100 pcs. To get a reviewable answer, send:

• Target quantity, and whether this is a repeat production run or a new build.
• The application - RC or UAV platform, and the axis or mechanism the servo drives.
• The controller you intend to use and the signal output type it drives.
• The supply voltage and how it is generated.
• The output spline and shaft you need to mate with.
• The mechanical envelope available, in millimetres.
• Packaging, labelling and shipping requirements.

Feasibility, scope and commercial terms are confirmed for the specific project rather than published as standard claims. Send project details to sales@linqdom.com.

Compatibility with a particular controller or system is not implied by this page - verify the exact configuration. The checks worth completing before integration are:

1. Voltage. The record lists an operating range of 6.0~7.4V DC. Provide a regulated rail in that range able to source the listed stall current of ≤5.2A at 6.0V and ≤6.2A at 7.4V.
2. Current budget. The record does not list a static current for this model, so no quiescent figure can be quoted. Use the stall figures for short-duration peak checks and confirm the static figure with the supplier if your supply budget depends on it.
3. Speed and voltage. The listed no-load speed is ≤0.15 sec./60° at 6.0V and ≤0.12 sec./60° at 7.4V. As general engineering guidance, the same servo is faster at the higher supply voltage, so a mechanism sized at 7.4V behaves differently at 6.0V.
4. Signal. The record lists a pulse width range of 500~2500μs but does not list a communication interface for this model. Confirm the signal interface and the command timing with the supplier and against your controller documentation before ordering.
5. Mechanical. The listed weight is 64±0.5g, the operating travel angle is 180°±10° and the mechanical limit angle is 210°. The record does not list a spline or shaft diameter, so confirm the output interface with the supplier before committing a horn or arm. Verify the mechanical envelope against the dimension drawing in module 02.

Category context: the RC Servos listing and the wider RC Parts & Accessories range on the LINQDOMTECH site.

• RC Servos category — https://www.linqdomtech.com/product-2-24-90-1.html
• RC Parts & Accessories — https://www.linqdomtech.com/product-2-24-1.html
• Products index — https://www.linqdomtech.com/product.html

1. Confirm the model: LS-036M-25 Brushless Metal Gear Digital Servo.
2. Confirm the order quantity; the standard MOQ for this servo line is 100 pcs.
3. Confirm the configuration points that affect the build, using the specification table in module 01.
4. Confirm mechanical fit against the dimension drawing before releasing the order.
5. Agree packaging, shipping terms and delivery details with the sales team before order confirmation.

For quotations, order details or an OEM/ODM review of the LS-036M-25, contact the LINQDOM team with your target quantity, application, controller, signal interface and mechanical requirements. Related pages: the RC Servos category listing, the wider RC Parts & Accessories range, and the LINQDOMTECH products index.

Email LINQDOMBrowse RC ServosVisit LINQDOM

sales@linqdom.com

• RC Servos category — https://www.linqdomtech.com/product-2-24-90-1.html
• RC Parts & Accessories — https://www.linqdomtech.com/product-2-24-1.html
• Products index — https://www.linqdomtech.com/product.html