LS-036FM-30 Brushless Metal Gear Digital Servo

The approved product record lists LS-036FM-30 as Brushless Metal Gear Digital Servo. The dimension drawing below is the approved drawing for this model - use it to check hub fit, arm clearance and mounting face before committing a build.

The scene photographs below come from the approved LS-036FM-30 image set and show the servo as supplied, in RC and UAV control use within the LINQDOM RC & UAV Parts & Accessories line. Before integrating, confirm every point against the specification table in module 01.

The full parameter set is in the specification table in module 01 - the points below are the decisions rather than a second parameter list.

• Supply range. The listed operating voltage is 6.0~8.4V DC, the widest range listed in this servo line. Confirm that your pack, regulator and connectors are rated for the top of that range, not only for 7.4V.
• Current. The listed stall current is ≤7A at 6.0V and ≤8A at 7.4V. That is a high figure; the supply, wiring and connectors must be able to carry it.
• Torque figures. The listed stall torque is ≥28.0 kgf.cm at 6.0V and ≥32.0 kgf.cm at 7.4V. These are stall values at two supply points, not a continuous working torque.
• Interface. The listed communication interface is PWM with a 500~2500μs pulse width range and a rotating direction of CCW (1000→2000μs). Confirm your controller's signal output type and command timing.
• Mounting. The output spline is 25T with a Ø5.9mm shaft and the listed weight is 70g. Check hub fit, arm clearance and whether 70g is acceptable for your airframe or payload budget.

• The widest listed operating voltage range in the servo line at 6.0~8.4V DC, which allows one servo to cover packs that run at 6.0V and at 8.4V.
• A listed stall torque of ≥32.0 kgf.cm at 7.4V and ≥28.0 kgf.cm at 6.0V, the highest torque figures listed among the models in this package.
• A listed no-load speed of ≤0.12 sec/60° at 7.4V and ≤0.14 sec/60° at 6.0V.
• A brushless motor with a metal gear train, as marked in the catalog type designation.
• A documented mechanical interface: 25T/Ø5.9mm spline, JR2.54 plug, 180° operating travel angle and a listed 70g weight.
• Consistent supply terms: the standard MOQ for this servo line is 100 pcs, and OEM/ODM requests are handled as project-specific enquiries.

LINQDOM is a Shenzhen-based B2B supplier with OEM/ODM sourcing and customization support, and the standard MOQ for this servo line is 100 pcs. To get a reviewable answer, send:

• Target quantity, and whether this is a repeat production run or a new build.
• The application - RC or UAV platform, and the axis or mechanism the servo drives.
• The controller you intend to use and the signal output type it drives.
• The supply voltage and how it is generated.
• The output spline and shaft you need to mate with.
• The mechanical envelope available, in millimetres.
• Packaging, labelling and shipping requirements.

Feasibility, scope and commercial terms are confirmed for the specific project rather than published as standard claims. Send project details to sales@linqdom.com.

Compatibility with a particular controller or system is not implied by this page - verify the exact configuration. The checks worth completing before integration are:

1. Voltage. The record lists an operating range of 6.0~8.4V DC. Provide a regulated rail inside that range that can source the listed stall current of ≤7A at 6.0V and ≤8A at 7.4V, with headroom for more than one axis stalling at once.
2. Current budget. Static current is listed as ≤30 mA at 7.4V. Use that for quiescent supply sizing; the stall figures of ≤7A and ≤8A are short-duration peak values and set the requirement for wiring and connectors.
3. Speed and voltage. The listed no-load speed is ≤0.14 sec./60° at 6.0V and ≤0.12 sec./60° at 7.4V. As general engineering guidance, note that the same servo is faster at the higher supply voltage, so a mechanism sized at 8.4V behaves differently from the same mechanism at 6.0V.
4. Signal. The listed communication interface is PWM with a 500~2500μs pulse width range and a rotating direction of CCW (1000→2000μs). Confirm the controller signal output type and its command timing.
5. Mechanical. The output spline is 25T with a Ø5.9mm shaft, the listed weight is 70g and the operating travel angle is 180° with a return angle deviation of ≤1°. Verify hub fit, arm clearance and mounting face against the dimension drawing in module 02.

Category context: the RC Servos listing and the wider RC Parts & Accessories range on the LINQDOMTECH site.

• RC Servos category — https://www.linqdomtech.com/product-2-24-90-1.html
• RC Parts & Accessories — https://www.linqdomtech.com/product-2-24-1.html
• Products index — https://www.linqdomtech.com/product.html

1. Confirm the model: LS-036FM-30 Brushless Metal Gear Digital Servo.
2. Confirm the order quantity; the standard MOQ for this servo line is 100 pcs.
3. Confirm the configuration points that affect the build, using the specification table in module 01.
4. Confirm mechanical fit against the dimension drawing before releasing the order.
5. Agree packaging, shipping terms and delivery details with the sales team before order confirmation.

For quotations, order details or an OEM/ODM review of the LS-036FM-30, contact the LINQDOM team with your target quantity, application, controller, signal interface and mechanical requirements. Related pages: the RC Servos category listing, the wider RC Parts & Accessories range, and the LINQDOMTECH products index.

Email LINQDOMBrowse RC ServosVisit LINQDOM

sales@linqdom.com

• RC Servos category — https://www.linqdomtech.com/product-2-24-90-1.html
• RC Parts & Accessories — https://www.linqdomtech.com/product-2-24-1.html
• Products index — https://www.linqdomtech.com/product.html